Code Stories · PressureTest
Table 1 (Cornell text): "Diameter of Pipe / Maximum Developed Length of the Pipe: 1-1/2 5" [sic]; 2 6'; 3 8'; 4 10'. Slope not to exceed 1/4" per foot." The 1-1/2 in. row reads 5 in. in the 2023 print; facts.json records this as a typo for 5 ft (2017 edition says five feet). 10.16(10)(b)1: "The vent pipe openings from a soil or waste pipe, except for toilets and similar fixtures, shall not be below the top weir of the trap." 10.16(1)(b): "No vent shall be installed within two pipe diameters of the trap weir."
Trap arm, 1-1/2 in. trap: 5 ft max (248 CMR 10.16(10) Table 1)
Trap arm, 2 in. trap: 6 ft max (248 CMR 10.16(10) Table 1)
Trap arm, 3 in. trap: 8 ft max (248 CMR 10.16(10) Table 1)
Trap arm, 4 in. trap: 10 ft max (248 CMR 10.16(10) Table 1)
Trap arm (Table 1) slope not to exceed 1/4 in. per foot (248 CMR 10.16(10) Table 1 note)
No vent within two pipe diameters of the trap weir (248 CMR 10.16(1)(b))
Floor-outlet toilet: vertical distance finish floor to horizontal drain centerline max 20 in., else individually vented (248 CMR 10.16(10)(c)1-2)
Exception to vent-below-weir for flat-bottom fixture of at least 144 sq in, vertical one size larger (248 CMR 10.16(10)(b)2.a-c)
A trap arm that runs completely full of water acts like an S-trap: the falling column of water pulls the seal out behind it (self-siphonage). The 1940 federal manual (BMS 66) controlled this by limiting the total fall from trap weir to vent fitting to one pipe diameter.
At 1/4 in. per foot, a pipe falls one diameter in four times its size in feet, which is where the old 1940 table (5, 6, 8 and 12 ft for 1-1/4, 1-1/2, 2 and 3 in.) came from. That is history.
Massachusetts today uses its own shorter table, 5-6-8-10 ft for 1-1/2, 2, 3 and 4 in. (10.16(10) Table 1), caps the slope at 1/4 in. per ft, and says the vent opening may not be below the trap weir. The 1940 manual also required at least 2 pipe diameters between weir and vent, and MA keeps that idea as its crown-venting ban (10.16(1)(b)).
BMS 66 section 1005 states the one-diameter-fall rule and the 2-to-48-diameter length range.
Source: https://archive.org/stream/plumbingmanual66subc/plumbingmanual66subc_djvu.txt
BMS 66 commentary turns the rule into the length table still taught today.
Source: https://archive.org/stream/plumbingmanual66subc/plumbingmanual66subc_djvu.txt
BMS 66 notes that a relief vent or stack vent within these limits can serve as the back vent.
Source: https://archive.org/stream/plumbingmanual66subc/plumbingmanual66subc_djvu.txt
Mnemonic: 'Five, six, eight, ten, and never below the weir.' The MA trap-arm ladder is 5 ft (1-1/2 in.), 6 ft (2 in.), 8 ft (3 in.) and 10 ft (4 in.), at no more than 1/4 in. per ft (248 CMR 10.16(10) Table 1). Warning: an older rule of thumb, 'pipe size times four', comes from the 1940 federal table and gives the wrong MA answer. For a 1-1/2 in. arm it gives 6 ft; MA says 5 ft.
A long trap arm is fine as long as you give it more pitch.
No. MA caps trap-arm slope at 1/4 in. per ft (10.16(10) Table 1 note) and does not allow the vent opening below the trap weir. Extra pitch only adds fall; it does not make a longer arm legal. The fix for a long arm is a vent closer to the trap.
The length limit is there to prevent clogs.
It is there to prevent self-siphonage. A trap arm that runs full acts like an S-trap.
The closer the vent to the trap, the better, even right at the crown.
No. MA prohibits any vent within two pipe diameters of the trap weir (248 CMR 10.16(1)(b)) and lists crown-vented traps as prohibited (10.08(2)(c)3). BMS 66 had the same 2-diameter minimum in 1940.
What is the maximum distance from a fixture trap to its vent (for a 1-1/2 inch trap arm)?
If a trap arm is too long, the fall along it puts the vent opening below the trap weir, and the flowing water can fill the pipe and siphon the seal. Limiting developed length for each pipe size keeps the vent close enough to protect the trap. For a 1-1/2 in. trap arm, 248 CMR 10.16 allows 5 feet (60 inches).
Under 248 CMR 10.16 Table 1, what is the maximum distance from a 2-inch fixture trap to its vent?
Massachusetts Table 1 limits a 2 in. trap arm to 6 ft of developed length at no more than 1/4 in. per foot of slope. The 8 ft figure belongs to other model codes or to the 3 in. row. A longer arm lets the trap siphon before the vent can relieve it.
Under 248 CMR 10.16 Table 1, what is the maximum distance from a 3-inch fixture trap to its vent?
Massachusetts Table 1 gives trap-to-vent limits of 5 ft for 1-1/2 in., 6 ft for 2 in., 8 ft for 3 in. and 10 ft for 4 in., with slope of no more than 1/4 in. per foot. The 12 ft figure comes from the IPC, not 248 CMR. A trap arm that is too long lets the trap siphon before the vent can relieve it.
pressuretest.me/learn/trap-arm-length/